You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 84 Next »

Step 7: Refine Mesh

It our mesh refine enough? Will the current mesh give us an accurate representation of the physical flow? Mesh density determine the truncation error of our simulation. With too little mesh density, the result we obtain will be inaccurate. With too many mesh elements,  we will be wasting unnecessary computational power (long computational time!). To get the optimum mesh density, we do mesh sensitivity analysis.

For this purpose, we will create three model with different mesh density. We will create a coarser mesh and a finer mesh and compare all the three meshes together.

For coarse mesh, reduce the mesh density by half of the original mesh. For fine mesh, double the mesh density compared to the original density.

Follow Step 1 through Step 5. At step 2, use the following edge mesh properties instead.

Higher Resolution ImageVisit page in new window

Label

Medium Mesh (Original)

Coarse Mesh

Fine Mesh

A

Interval Count: 36, Double First Length: 0.5

Interval Count: 24, Double First Length: 0.7

Interval Count: 54, Double First Length: 0.3

B

Interval Count: 36, Double First Length: 0.2

Interval Count: 24, Double First Length: 0.3

Interval Count: 54, Double First Length: 0.12

C

Interval Count: 30, First Length: 0.1

Interval Count: 20, First Length: 0.2

Interval Count: 45, First Length: 0.09

D

Interval Count: 18

Interval Count: 12

Interval Count: 27

E

Interval Count: 90, First Length: 0.1

Interval Count: 60, First Length: 0.15

Interval Count: 135, First Length: 0.07

F

Interval Count: 36

Interval Count: 24 

Interval Count: 54

G

Interval Count: 72

Interval Count: 48

Interval Count: 108

H

Interval Count: 30

Interval Count: 20

Interval Count: 45

I

Interval Count: 36, Double First Length: 0.05

Interval Count: 24, Double First Length: 0.07

Interval Count: 54, Double First Length: 0.03

You can also change the appropriate parameters (interval count and
first length) in your previous journal file to obtain different meshes.

To double the mesh density, the interval count is increased by factor of 1.5. The first length is decreased by a factor of about 1.5. To half the mesh density, the interval count is decreased by factor of 1.5. The first length is increased by a factor of about 1.5. Think about why it is so. 


After that, you should have three meshes with following mesh elements.


Coarse

Medium

Fine

No. of cells

6240

14040

31590

   

Drag Coefficient Comparison

For each mesh, take note of the drag coefficient and compare with each other.


Coarse

Medium

Fine

Cd

2.4981

2.4941

2.4927

% dif

0.160378

0

0.056132

Taking medium as benchmark, we compare coarse and fine mesh. Note that the difference in drag coefficient between three meshes is negligibly small. For analysis of drag coefficient, it seems that coarse mesh provides enough resolution.

Pressure Coefficient Comparison

Let's analyze pressure coefficient plot around cylinder for three different mesh before we conclude which mesh to use. Let's start with a coarse mesh.

Plot > XY Plot...

Change the Y Axis Function to Pressure..., followed by Pressure Coefficient. Then, select cylinder under Surfaces. Check the option Write to File.

Click Write...
 
Enter the file name and directory to save.
 
Do the same for medium and fine meshes by opening different case and data files.
 
After that, open the files that you have written with excel spreadsheet. Compile and plot the data accordingly.
 

Higher Resolution ImageVisit page in new window
 

A quick and dirty way plotting three different mesh is to use FLUENT directly. Plot > XY Plot... You can Load File... that you have saved previously. However, using this way, you have less control of how you can present the data and is not recommended for report presentation.

 
 

Go to Problem 1

See and rate the complete Learning Module

Go to all FLUENT Learning Modules\

  • No labels