Skip to end of metadata
Go to start of metadata

Step 6: Specify boundary conditions

Recall that the BCs for face 1 are:
u=0 at node A (keypoint 1)
v=0 at all face 1 nodes
w=0 along AB (line L7)

These BCs are in the cylindrical coordinate system. Switch to this coordinate system:

Utility Menu > WorkPlane > Change Active CS to > Global Cylindrical

We'll work with areas while specifying the BCs. So plot areas: Utility Menu > Plot > Areas

Rotate Nodal Coordinate System

In ANSYS, the boundary constraints are applied in the nodal coordinate system which by default is parallel to the global Cartesian system. Since we want to apply the constraints in the global Cylindrical coordinate system, we need to rotate the nodal coordinate system into the active coordinate system (i.e. Cylindrical) using the nrotat command.

Type nrotat,all in the Input window.

To see the help page for nrotat, type help,nrotat in the Input window.

Apply u=0 at Node A

Main Menu > Preprocessor > Loads > Define Loads > Apply > Structural > Displacement > On Nodes

Select node at A (keypoint 1) in the lower-right corner and click OK in the pick menu. Select UX for DOFs to be constrained. You can leave the Displacement value blank since the default is zero. Click OK. You'll see an arrow symbol in the Graphics window indicating that the node A is constrained in the radial direction.

Select Nodes on Face 1

ANSYS provides extensive capabilities, referred to as "select logic", for selecting a subset of the full model using various criteria. We'll use select logic to select the nodes on face 1. We'll first select the area corresponding to face 1 and then select the nodes attached to this area.

Utility Menu > Select > Entities

Select Areas from the pull-down menu at the top. Make sure By Num/Pick is selected below that. Click Apply.

Hold down the left mouse button until face 1 is picked. Click OK in the pick menu.

Only the area corresponding to face 1 is selected currently. Verify this: Utility Menu > Plot > Areas.

Next we'll select the nodes attached to the selected area. In the Select Entities menu, select Nodes from the pull-down menu at the top and Attached to below that. Select Areas, All below that. Click Apply.

Check that only nodes attached to face 1 are currently selected: Utility Menu > Plot > Nodes

Apply v=0 on Face 1

Main Menu > Preprocessor > Loads > Define Loads > Apply > Structural > Displacement > On Nodes

Pick All nodes in the pick menu. Select UY for DOFs to be constrained and click OK. You'll see arrow symbols in the Graphics window indicating that the nodes on face 1 are constrained in the circumferential direction.

We can use Pick All since only the nodes on face 1 are currently selected. ANSYS commands apply only to the currently selected entities.

Select Nodes Along AB

Plot lines: Utility Menu > Plot > Lines

In the Select Entities menu, select Lines from the pull-down menu at the top and By Num/PickApply below that. Click OK.

Click on line AB (L7) and OK in the pick menu.

Next we'll select the nodes attached to the selected line. In the Select Entities menu, select Nodes from the pull-down menu at the top and Attached to below that. Select Lines, All below that. Click Apply.

Check that only nodes attached to line AB are currently selected: Utility Menu > Plot > Nodes

Apply w=0 Along AB

Main Menu > Preprocessor > Loads > Define Loads > Apply > Structural > Displacement > On Nodes

Pick All nodes in the pick menu. Select UZ for DOFs to be constrained and click OK.

Define Function

Recall that the BCs for face 2 are:
v=0.0001(rc-r) at all face 2 nodes
w=0 along CD (line L5)

Since the BC on v is a function of the spatial coordinates, we need to define a function to apply this BC. Bring up the function editor:

Utility Menu > Parameters > Functions > Define/Edit...

You can enter the function using the calculator buttons or type it in. The variables such as TIME, X, Y etc. that are available for defining functions are in the pull-down list below the Result field. For entering the spatial coordinates X and Y, use the pull-down menu. Enter the function:

Note that variables are enclosed in squiggly brackets.

Save the function: Function Editor > File > Save

Use vface2.func for the filename.

Close the function editor.

Define Table from Function

ANSYS doesn't allow the user to use functions directly while applying loads to a model. Instead, one has to go through the additional step of using a "Function Loader" that retrieves the function and loads it as a Table array. The Table array can then be applied to the model. The process is not exactly elegant but then we are engineers.

Utility Menu > Parameters > Functions > Read From File

Select vface2.func and click Open.

Enter vface2 for Table parameter name.

Observe that ANSYS displays the equation that will be used in creating the Table array. Click OK.

Select Nodes on Face 2

Start by selecting the whole model to undo previous selects.

Utility Menu > Select > Everything

Utility Menu > Plot > Areas

To select the nodes on face 2, we'll follow the same procedure as for face 1.

Utility Menu > Select > Entities

Select Areas from the pull-down menu at the top. Select By Num/Pick below that. Click Apply.

Hold down the left mouse button until face 2 is picked. Click OK in the pick menu.

Only the area corresponding to face 2 is selected currently. Verify this: Utility Menu > Plot > Areas.

Next we'll select the nodes attached to the selected area. In the Select Entities menu, select Nodes from the pull-down menu at the top and Attached to below that. Select Areas, All below that. Click Apply.

Check that only nodes attached to face 2 are currently selected: Utility Menu > Plot > Nodes

Apply BC for v on Face 2

We'll use the vface2 table that we created to apply this BC.

Main Menu > Preprocessor > Loads > Define Loads > Apply > Structural > Displacement > On Nodes

Pick All nodes in the pick menu. Select UY for DOFs to be constrained. Select Existing table under Apply as and click OK.

We have defined only one table (VFACE2) and that is automatically selected. Click OK.

You'll see arrow symbols in the Graphics window indicating that the nodes on face 2 are constrained in the circumferential direction.

Select Nodes Along CD

Plot lines: Utility Menu > Plot > Lines

In the Select Entities menu, select Lines from the pull-down menu at the top and By Num/Pick below that. Click Apply.

Click on line CD (L5) and OK in the pick menu.

Next we'll select the nodes attached to the selected line. In the Select Entities menu, select Nodes from the pull-down menu at the top and Attached to below that. Select Lines, All below that. Click Apply.

Check that only nodes attached to line CD are currently selected: Utility Menu > Plot > Nodes

Apply w=0 Along CD

Main Menu > Preprocessor > Loads > Define Loads > Apply > Structural > Displacement > On Nodes

Pick All nodes in the pick menu. Select UZ for DOFs to be constrained. Select Constant value under Apply as and click OK.

Utility Menu > Select > Everything

Utility Menu > Plot > Volumes

Save your work:Toolbar > SAVE_DB

Go to Step 7: Solve!

See and rate the complete Learning Module

Go to all ANSYS Learning Modules

  • No labels