You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 46 Next »

Unknown macro: {float}

Illustration of non-linear chemical doser

Introduction

The non-linear dose controller was redesigned in order to reduce the amount of aeration caused as water traveled through the plant. For more information about the theory of the non-linear dose controller see the page for the original non-linear CDC design.

Methods

Sizing the Orifice

The orifice between the rapid mix and flocculation tanks is designed to produce a difference in water level high that can then be sensed by a float which would then change the flow rate of aluminum sulfate:

Unable to find DVI conversion log file.

where

  • Unable to find DVI conversion log file. is the difference in head loss between the rapid mix and flocculation tank
  • K orifice is the required minor loss coefficient through the orifice
  • V jet is the velocity in the dosing tube

This head loss was then used to determine the velocity of the water through the orifice and the residence time. Using the following equations:

Velocity of Jets:

Unable to find DVI conversion log file.

where

  • V jet is the velocity of the jet
  • Q is the flow rate through the system
  • C d is the vena contracta coefficient for exit condition in orifice
  • A orifice is the area of the orifice

Residence time :

Unable to find DVI conversion log file.

where

  • Unable to find DVI conversion log file. is the residence time
  • d orifice is the diameter of the orifice
  • V jet is the velocity of the jet

Once these values were determined, we were able to calculate the energy dissipation rate using the following equation:

Unable to find DVI conversion log file.

where

  • Unable to find DVI conversion log file. is the energy dissipation rate
  • g is gravity
  • Unable to find DVI conversion log file. is the head loss
  • Unable to find DVI conversion log file. is the residence time

We sought to keep the energy dissipation rate between .5 and 1 W/kg so that molecular scale diffusion works and in order for small scale turbulent mixing to be effective.

Lever Arm and Float

We first must determine the size of the counterweight on the doser arm in order to ensure that the dosage will only be a function of the difference in water height in the flocculation and rapid mix tanks. The mass of the weight is calculated by determining the mass of the doser when full.

Unable to find DVI conversion log file.

where

  • D actual is the difference between the given diameter of the dosing tube and the measured diameter of the dosing tube
  • Unable to find DVI conversion log file. is the density of water
  • Unable to find DVI conversion log file. is the mass of the doser empty

The size of the float can be determined using a moment balance around the pivot of the lever arm. This is to ensure that a change in head in the entrance tank will cause a similar change in the relative height of the float. The float was sized using the same float sizing algorithm used by the linear CDC. Based on this we found that a float of 13.3 inches would theoretically be able to measure a .25cm height difference.

Conclusion

Based on our calculations, we found that an orifice of 8cm would give us an acceptable energy dissipation rate of .927 W/kg and would require a 13.3in float. This float would have a .25cm sensitivity over a 15.2cm height difference.

Unknown macro: {float}

Graph showing the non-linear relationship between the head loss vs. the flow rate through a 8cm diameter orifice

Additionally we found 2 solutions with multiple orifices. We did this because more orifices at a smaller diameter will keep energy dissepation constant while increasing overall headloss across the system. The first solution gave us 8 orifices with a 4.5cm diameter and a minimum energy dissipation rate of .831.

Unknown macro: {float}

Graph showing the non-linear relationship between the head loss vs. the flow rate through eight 4.5cm diameter orifices

The second solution gave us 175 orifices with a 2 cm diameter and a minimum energy dissipation rate of .496.

Unknown macro: {float}

Graph showing the non-linear relationship between the head loss vs. the flow rate through 175 2cm diameter orifices
  • No labels