Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Include Page
FLUENT Google Analytics
FLUENT Google Analytics
Include Page
Flat Plate Boundary Layer - Panel
Flat Plate Boundary Layer - Panel

Mesh

Create Mesh

HTML
<iframe width="560" height="315" src="https://www.youtube.com/embed/g-cHqbx9uRk" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe>

 

 

 

Increase Near-Wall Resolution

HTML
<iframe width="560" height="315" src="https://www.youtube.com/embed/oSP6Mh3A-Gs" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe>

 

 

 

Label Boundaries

HTML
<iframe width="560" height="315" src="https://www.youtube.com/embed/zvDWmwrPIMU" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe>



Go to Step 4: Model Setup

Go to all FLUENT Learning Modules

Panel

Problem Specification
1. Pre-Analysis and Start-up
2. Geometry
3. Mesh
4. Setup (Physics)
5. Solution
6. Results
7. Verification and Validation

...

TitleUnder Construction

Step 3: Mesh

Step 3: Mesh

In this section the geometry will be meshed with 500 elements. That is, the pipe will be divided into 100 elements in the axial direction and 5 elements in the radial direction.

Launch Mesher

In order to begin the meshing process, go to the Workbench Project Page, then (Double Click) Mesh.

...

In ANSYS Mesher, make sure that the unit we are working on is meter Metric unit. On the top menu, click on Units and make sure that Metric (m, kg, N, s, V, A) is selected.

...

Meshing Method

We would also like to create a structured mesh where the opposite edges correspond with each other. Let's insert a Mapped Face mesh.  Under Outline, right click on Mesh, move cursor to Insert, and select Mapped Face Meshing. Alternatively, you can click on Mesh Control on the third menu and select Mapped Face Meshing. Finally select the flat plate surface body in the Graphics window and click Apply next to Geometry.

This is what you should end up with;
Image Removed
 

Edge Sizing

Now let us move on to specify the element sizing along the pipe radial direction.
Outline > Mesh > Insert > Sizing
In the Graphics window, select both the top and bottom edges of the geometry (click on the Edge tab on the Fluid flow Fluent - Mesh window and then press Ctrl + mouse click to multiple select). Under Details of "Edge Sizing", click Apply next to Geometry. Change the edge sizing definition Type to Number of Divisions. Enter 50 for Number of Divisions. Next to Behaviour, change Soft to Hard

You should have something that looks like this;
Image Removed
 
Now continue with the sizing in the y-axis direction.

Outline > Mesh > Insert > Sizing
In the Graphics window, select the left side edge of the geometry (press Ctrl + mouse click to multiple select). Under Details of "Edge Sizing", click Apply next to Geometry. Change the edge sizing definition Type to Number of Divisions. Enter 60 for Number of Divisions. Next to Behaviour, change Soft to Hard (This is to overwrite the sizing function employed by ANSYS Mesher). Then under Bias Type enter 100.

Image Removed
 

 You should get this;
Image Removed
 
Now follow the same steps for the right side edge sizing as delineated for the left side above.

...

We have specified all the meshing conditions. Click Update on the third menu to see the mesh.

It should look like this;
Image Removed

Click on Mesh and look under Details of "Mesh", next to Statistics, you should see that we have 6120 Elements for our mesh.

Create Named Selection

...

Select the left edge and right click and select Create Named Selection. Enter Inlet and click OK. Under Outline, you will see the name Inlet under Named Selections. Note that the flat plat surface is designated as the center line.

...

Finally, click Update.

Go to Step 4: Setup (Physics)