• Created by user-8da17, last modified by user-22e4c on Nov 30, 2009

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 24 Next »

Prototype Doser Frame

Abstract

A full scale proto-type is being created.  This model will allow us to run full flow/ full scale accuracy tests in the lab. Additionally, this model will be taken to the EP3 conference this spring.  With this proto-type we will be able to demonstrate the functionality and flexibility of our chemical doser.

Proto-type Design

The proto-type is made up of two main components: the structural frame work and the moving lever-arm.  The frame components are constructed using a modular aluminum framing system manufactured by a company called 80/20. Affectionately called "The Industrial Erector Set," this company offers a wide variety of components along with an Auto-cad plug-in of each of their components. With these tools, we have been able to design and evaluate multiple proto-types. Additionally, their T-bar design will allow us to mount extra components that can be mounted with any standard "National Course" thread.  All accessories are readily available components purchased through McMaster-Carr.

The dimensions of the structural framework is based on the actual dimensions of the entrance tank of the Agalteca plant.  We have reduced the width to 1/2 meter as a space/material-cost saving measure but otherwise accurately reflect the entrance tank dimensions. 

Entrance tank dimensions and elevation are a critical criteria in plant operations.  All headloss throughout the plant must be accounted for in the entrance tank.  Furthermore, the addition of the rapid-mix tube has added to the depth of the entrance tank.  Full analysis of these parameters can be found on the Agalteca Page (***Karen, please show me how to link to this page.)

 **Monica- make a drawing for Agalteca headlosses in entrance tank

Additionaly, the the frame work includes a table to hold a small stock tank and another table to hold the constant-flow device. As determined in the design of the constant head device, there should be ideally 30 cm between the orifice and the low water lever of the stock tank. This dimension has been taken into account in our design. **Find and link this page

We have designed three different lever systems with the current design presented here. (Please label the figure and what you are showing in each.)**Harry can you work on this section?  Label components and describe each item in detail.  Actually, I think we have an update version that shows the eye-bolts.  Let me know when you are working on this and I will email it to you. 



There are a number of constraints in the design of this lever arm. First, we need to facilitate a way to attach the floats and counter-weight. Secondly, we must have a way to adjust the distance the orifice travels down the arm. It was also requested that the operators be given a means to manually "shut off" the flow. This can be accomplished by moving the orifice directly in line with the pivot. We have also attempted to accommodate a second slide to facilitate attaching a second dosing pH control system. It is preferred that both slides operate on the same side of the lever to allow the operator easier access.

As shown in our current design, most of these constraints can be met. We are using a slide mechanism that has a manual "brake" which allows the slide to be clamped in any position. (Describe how this "brake" mechanism works. Label figure below)

 

We have not found a way to get both slides on the same side of the lever arm as their "open channel dosing tubes" would interfere with each other. Currently, the slides are on opposite sides which could be awkward for the operator to manipulate. One solution would be to mount the lever-arm across the diagonal of the tank. The operator would then have easier access to both sides of the lever-arm. We are considering this option.

Currently, each slide can be moved independently and can be moved to the center line to allow the operator to secure flow if needed. The floats and weights will be attached via the brackets at the endpoints. These will most likely become eye-bolts as they are easy to obtain and will attach on the center-line instead of the sides. (Can you refer to the figure that shows this?)

The AutoCad Drawing can be viewed Here

 Useful 80/20 information

 80/20 Inc. is a manufacturer of modular aluminum framing system.  80/20 components are used extensively throughout our lab and specifically in this project.  This section provides some details to assist getting started with these components and using them in design. 

http://www.8020.net/  This is the main web page for this company.  Available is a complete on-line catalog, price catalog and design ideas.  Design is made easier using their "Auto-cad Plug-In."  All components and frames are available with this Plug-In making requiring only limited Auto-cad knowledge for a professional looking design. 

This Plug-In, called Auto-Quoter, is used by the distributors to generate their price-quote.  Auto-Quoter can be downloaded on to any computer that is running Auto-cad and is free.  This program leads to greater accuracy when ordering and less chance of error as the Bill of Materials is generated directly from the Auto-cad drawing.

 Two local distributors are: Ralph W. Earl Inc.

5930 E.Molloy Rd.

Syracuse NY 13220

315-454-4431

rwearl@rwearl.com

Specifically- Bob Prosher:bproscher@rwearl.com.  Competent and helpful salesman.
Hughes Industrial

9685 Main St.

Clarence NY 14031

800-759-8374

www.hughesind.com

 Ordering Information

 The Bill of Material as generated by the AutoQuoter program and is attached.  Bob Proscher from Ralph W. Earl Inc was able to procure a 40% discount for us on materials.  The order for these components was submitted to Christene Day on November 17,2009.  We are currently waiting on receipt of the materials to continue on the project.

**Attach the BOM here

Bibliography

Deliverables

By the end of the semester we intend to have a functional, full scale non-linear chemical doser.In order to accomplish this, this sub-group needs to complete the following:

  • Complete final changes to Autocad drawing to represent changes in the bracketing.
  • Talk to Paul Charles about fabrication of the bushing and drilling of the lever-arm
  • Update Material's List
  • Contact 80/20 distributor about pricing. Plan to discuss the possibility of having them sponsor our frame
  • Order and receive components. Assemble according to Autocad Dwg.
  • Install hydraulic components
  • No labels