Include Page | ||||
---|---|---|---|---|
|
Include Page | ||||
---|---|---|---|---|
|
Physics Setup
Your current Workbench Project Page should look comparable to the following image. Regardless of whether you downloaded the mesh and geometry files or if you created them yourself, you should have checkmarks to the right of Geometry and Mesh.
Next, the mesh and geometry data need to be read into FLUENT. To read in the data (Right Click) Setup > Refresh in the Workbench Project Page as shown in the image below.
After you click Update, a question mark should appear to the right of the Setup cell. This indicates that the Setup process has not yet been completed.
Launch Fluent
Double click on Setup in the Workbench Project Page which will bring up the FLUENT Launcher. When the FLUENT Launcher appears change the options to "Double Precision", and then click OK as shown below. The Double Precision option is used to select the double-precision solver. In the double-precision solver, each floating point number is represented using 64 bits in contrast to the single-precision solver which uses 32 bits. The extra bits increase not only the precision, but also the range of magnitudes that can be represented. The downside of using double precision is that it requires more memory.
Twiddle your thumbs a bit while the FLUENT interface starts up. This is where we'll specify the governing equations and boundary conditions for our boundary-value problem. On the left-hand side of the FLUENT interface, we see various items listed under Problem Setup. We will work from top to bottom of the Problem Setup items to setup the physics of our boundary-value problem. On the right hand side, we have the Graphics pane and, below that, the Command pane.
Check and Display Mesh
First, the mesh will be checked to verify that it has been properly imported from Workbench. In order to obtain the statistics about the mesh (Click) Mesh > Info > Size, as shown in the image below.
Then, you should obtain the following output in the Command pane.
The mesh that was created earlier has 22000 elements. Note that in FLUENT elements are called cells. The output states that there are 22000 cells, which is a good sign. Next, FLUENT will be asked to check the mesh for errors. In order to carry out the mesh checking procedure (Click) Mesh > Check as shown in the image below.
You should see no errors in the Command Pane. Now, that the mesh has been verified, the mesh display options will be discussed. In order to bring up the display options (Click) General > Mesh > Display as shown in the image below.
The previous step should cause the Mesh Display window to open, as shown below. Note that the Named Selections created in the meshing steps now appear.
You should have all the surfaces shown in the above snapshot. Clicking on a surface name in the Mesh Display menu will toggle between select and unselect. Clicking Display will show all the currently selected surface entities in the graphics pane. Unselect all surfaces and then select each one in turn to see which part of the domain or boundary the particular surface entity corresponds to (you will need to zoom in/out and translate the model as you do this). For instance, if you select wall, outlet, and centerline and then click Display you should then obtain the following output in the graphics window.
Now, make sure all 5 items under Surfaces are selected. The button next to Surfaces selects all of the boundaries while the
button deselects all of the boundaries at once. Once all the 5 boundaries have been selected click Display, then close the Mesh Display window. The region displayed in the graphics window corresponds to our solution domain.
Define Solver Properties
In this section the various solver properties will be specified in order to obtain the proper solution for the laminar pipe flow. First, the axisymmetric nature of the geometry must be specified. Under General > Solver > 2D Space select Axisymmetric as shown in the image below.
Next, the Viscous Model parameters will be specified. In order to open the Viscous Model Options Models > Viscous - Laminar > Edit.... By default, the Viscous Model options are set to laminar, so no changes are needed. Click Cancel to exit the menu.
Now, the Energy Model parameters will be specified. In order to open the Energy Model Options Models > Energy-Off > Edit.... For incompressible flow, the energy equation is decoupled from the continuity and momentum equations. We need to solve the energy equation only if we are interested in determining the temperature distribution. We will not deal with temperature in this example. So leave the Energy Equation set to off and click Cancel to exit the menu.
Define Material Properties
Now, the properties of the fluid that is being modeled will be specified. The properties of the fluid were specified in the Problem Specification section. In order to create a new fluid (Click) Materials > Fluid > Create/Edit... as shown in the image below.
In the Create/Edit Materials menu set the Density to 1kg/m^3 (constant) and set the Viscosity to 3.61e-2 kg/(ms) (constant) as shown in the image below.
Click Change/Create. Close the window.
Define Boundary Conditions
At this point the boundary conditions for the four Named Selections will be specified. The boundary condition for the inlet will be specified first.
Inlet Boundary Condition
In order to start the process (Click) Boundary Conditions > inlet > Edit... as shown in the following image.
Note that the Boundary Condition Type should have been automatically set to velocity-inlet. Now, the velocity at the inlet will be specified. In the Velocity Inlet menu set the Velocity Specification Method to Magnitude, Normal to Boundary, and set the Velocity Magnitude (m/s) to 0.277 m/s, as shown below.
Then, click OK to close the Velocity Inlet menu.
Outlet Boundary Condition
First, select outlet in the Boundary Conditions menu, as shown below.
As can be seen in the image above the Type should have been automatically set to pressure-outlet. If the Type is not set to pressure-outlet, then set it to pressure-outlet. Now, no further changes are needed for the outlet boundary condition.
Centerline Boundary Condition
Select centerline in the Boundary Conditions menu, as shown below.
As can be seen in the image above the Type has been automatically set to wall which is not correct. Change the Type to axis, as shown below.
When the dialog boxes appear click Yes to change the boundary type. Then click OK to accept "centerline" as the zone name.
Pipe Wall Boundary Condition
First, select Wall in the Boundary Conditions menu, as shown below.
As can be seen in the image above the Type should have been automatically set to wall. If the Type is not set to wall, then set it to wall. Now, no further changes are needed for the wall boundary condition.
Save
In order to save your work (Click)File > Save Project as shown in the image below.