...
AguaClara Filtration Team
Abstract
The challenge for the 2010 Spring AguaClara Filtration Team is to design a filtration system for the AguaClara water treatment plant. The filtration system must meet the following requirements: reliably treat the current AguaClara effluent water with a turbidity ranging from 5 to 10 NTU to an effluent turbidity less than 1 NTU, not require any electricity, make minimal use of specialized components that would be difficult to acquire in remote communities, and the system should be easy to construct and to maintain.
Currently, the filtration team has conducted research in four fields: stacked filtration, clear well backwash, foam filtration, and siphon-aided backwash. For each subject, we conducted a literature review of existing technology and research. We then developed initial designs based on our research and proceeded to test the fundamental theories behind our design. For example, the foam filtration sub team tested the effectiveness of foam in reducing the turbidity of the water while the clear well backwash team developed a bench scale model to test the empirical equations behind the design. We have currently ruled out further research in clear well and siphon-aided backwash design for economic reasons. Table 1 Filtration Design Tracker summarizes our current progress in filtration research.
Table 1 Filtration Design Tracker
...
Method & Result and Discussions for each sub team
...
The goal of our research is to evaluate the feasibility of a siphon-aided backwash design to be used for a sand or mixed-media down-flow filter. The benefits of siphon-aided backwash are:
1) The height of the clear-well does not need to be equal to the head pressure required to attain 30%-50% expansion.
2) The filter bed can be right next to the clear-well, connected via an open pipe without a valve. Flow of water into and out of the clear-well will be controlled by valves on the influent and backwash manifolds.
3) Using 55 gallon HDPE barrels, we will create a system of parallel filters surrounding a shared clear-well. By backwashing the filters out of phase, we will reduce the demand for a large clear-well. Additionally, the down flow filters will be filling the clear-well while the other filters being backwashed draw from it. This allows faster clear-well recharge rates and shortens the time between consecutive backwash cycles.
We are discontinuing research of the Siphon-Aided Backwash for the following reasons: it is a pressurized system which prevents the operator from properly observing the operation of the system, it is not economically feasible because it requires either the construction of one large clear well or multiple smaller clear wells, and the filtration system itself would require the construction of one large or multiple small filtration systems.
Foam Filtration
Currently, an AguaClara plant can produce effluent water after sedimentation with a turbidity of about 5 NTU. Our goal is to reduce the effluent turbidity to less than 1 NTU. One potential method of accomplishing this is adding a filtration unit to the AguaClara plants.
Numerous techniques of water filtration are in use today, most of which involve the use of sand as the porous media. After preliminary research revealed a lack of information on foam filtration, our team has decided to focus on investigating the actual filtering capacity of a polyurethane foam material as opposed to the traditional method of sand filtration. With proper implementation, a foam filter could reduce the amount of water that is wasted during the backwash cycle of a traditional sand filter. A foam filter could also potentially require less area, and be less expensive to build than a traditional sand filter.
Clear Well Backwash Filtration System
The elevation of the clear well is between that of the filter beds and the effluent source of the sedimentation tank. During normal operation, this elevation difference allows effluent from the sedimentation tank to flow through the filter and subsequently to the clear well. Backwash requires approximately ten times the flow rate as normal operation. Filtered water can be sent to the clear by closing the valve leading to the distribution lines whereby water accumulates in the filter beds until the head difference between the filter and the clear well is sufficient and filtered water is diverted to the clear well.
We based our initial design on empirical granular filtration equations from existing literature (reference) on granular filtration. A bench-scale model of our system was built and tested to observe the discrepancy between the actual and the calculated fluidization velocity required to achieve a target bed expansion. We noted an increasing difference between those two sets of values that prompted us to hypothesize that, if we were to base our design on these empirical equations, we need to implement a significant safety factor.
Figure 1: Clear Well Filtration Design
We are discontinuing research of the Clear Well Filtration System because it is not economically feasible due to the large size of the clear well needed to back wash the filters.
Stacked Filtration System
So far, we have created a preliminary design for a stacked filtration system for the Agalteca Plant. It is a granular, mixed (or vertical) flow filtration system consisting of four separate rapid sand filtration units. The basic concept of our design is to make the backwash flow rate equal the filtration flow rate in order to use the effluent water from the sedimentation tank to backwash. We have chosen this concept because of the following benefits:
1) Relatively small size of the entire filtration system compared to other granular filtration systems researched.
2) Availability of the materials that would be involved in its construction.
3) Relative ease of operation.
4) If given full plant flow, the ability to conduct backwash while maintaining normal filtration operations in at least half capacity.
...
Advice and Future Challenge to the Future Filtration Team
Past Research - Terminated Methods
Spring 2010 Filtration Team Teach In
...