Wiki Markup |
---|
{float:right|border=2px solid black|width=300px} !Non Linear Doser Diagram.jpg|width=300px, align=centrecenter! h5. Illustration of non-linear chemical doser {float} h3. Introduction The |
Introduction
The non-linear
...
dose
...
controller
...
was
...
redesigned
...
in
...
order
...
to
...
reduce
...
the
...
amount
...
of
...
aeration
...
caused
...
as
...
water
...
traveled
...
through
...
the
...
plant.
...
For
...
more
...
information
...
about
...
the
...
theory
...
of
...
the
...
non-linear
...
dose
...
controller
...
see
...
the
...
page
...
for
...
the
...
...
...
...
Methods
Sizing the Orifice
The orifice between the rapid mix and flocculation tanks is designed to produce a difference in water level high that can then be sensed by a float which would then change the flow rate of aluminum sulfate:
Latex |
---|
|Nonlinear Chemical Dose Controller]. +(How was it designed? What were important components?)+ h3. Methods h4. Sizing the Orifice The orifice between the rapid mix and floculation tanks is designed to produce a difference in water level high that can then be sensed by a float which would then change the flow rate of aluminum sulfate: +(can you show how this is accomplished? Animation?)+ {latex}$$ \Delta H = K_{_{orifice} } {{V_{jet} ^2 } \over {2*g}} $$ {latex} where * {latex} |
where
Latex $$ \Delta H $$
...
is
...
- the
...
- difference
...
- in
...
- head
...
- loss
...
- between
...
- the
...
- rapid
...
- mix
...
- and
...
- flocculation
...
- tank
- K orifice is the required minor loss coefficient through the orifice
- V jet is the velocity in the dosing tube
This head loss was then used to determine the velocity of the water through the orifice and the residence time. Using the following equations:
Velocity of Jets:
Latex |
---|
$$V_ * K ~orifice~ is the required minor loss coefficient through the orifice * V ~jet~ is the velocity in the dosing tube This head loss was then used to determine the velocity of the water through the orifice and the residence time. +(Why?)+ Using the following equations: Velocity of Jets: {latex} $$ V\_ {jet} = {Q \over {C_d *A_{orifice} }} $${latex} where * V ~jet~ is the velocity of the jet * Q is the flow rate through the system * C ~d~ is the vena contracta coefficient for exit condition in orifice * A ~orifice~ is the area of the orifice Residence time : {latex} |
where
- V jet is the velocity of the jet
- Q is the flow rate through the system
- C d is the vena contracta coefficient for exit condition in orifice
- A orifice is the area of the orifice
Residence time :
Latex |
---|
$$ \theta = {{d_{orifice} } \over {V_{jet} }} $${latex} where * {latex} |
where
Latex $$ \theta
...
$$
...
is
...
- the
...
- residence
...
- time
- d orifice is the diameter of the orifice
- V jet is the velocity of the jet
Once these values were determined, we were able to calculate the energy dissipation rate using the following equation:
Latex |
---|
* d ~orifice~ is the diameter of the oricifice * V ~jet~ is the velocity of the jet Once these values were determined, we were able to calculate the energy dissipation rate using the following equation: {latex}$$ \varepsilon = {{g*\Delta H} \over \theta } $${latex} where We sought to keep the energy dissipation +rate+ between .5 and 1 W/kg so that molecular scale diffusion works and in order for small scale turbulent mixing to be effective. h4. Lever Arm and Float We first must determine the size of the counterweight on the doser arm in order to ensure that the dosage will only be a function of the difference in water height in the flocculation and rapid mix tanks. The mass of the weight is calculated by determining the mass of the doser when full. {latex} $$ m\_ {doserful} = {actual}} \over 2})^2 \*\pi \*1m"linktype="raw" linktext=" |
where
is the energy dissipation rateLatex $$ \varepsilon $$
- g is gravity
is the head lossLatex $$ \Delta H $$
is the residence timeLatex $$ \theta $$
We sought to keep the energy dissipation rate between .5 and 1 W/kg so that molecular scale diffusion works and in order for small scale turbulent mixing to be effective.
Lever Arm and Float
We first must determine the size of the counterweight on the doser arm in order to ensure that the dosage will only be a function of the difference in water height in the flocculation and rapid mix tanks. The mass of the weight is calculated by determining the mass of the doser when full.
Latex |
---|
$$ m_{doserful} = [({{.375in} \over 2})^2 \*\pi \*25cm + ({{D\_ {actual} } \over 2})^2 \*\pi \*1m" class="linkerror">({{.375in} \over 2})^2 \*\pi \*25cm + ({{D\_ {actual} } \over 2})^2 \*\pi \*1m]\rho _ {water} + m\_ {doser} $$ |
where
- D actual is the difference between the given diameter of the dosing tube and the measured diameter of the dosing tube
is the density of waterLatex $$ \rho _{water} $$
is the mass of the doser emptyLatex $$ m_{doser} $$
The size of the float can be determined using a moment balance around the pivot of the lever arm. This is to ensure that a change in head in the entrance tank will cause a similar change in the relative height of the float. The float was sized using the same float sizing algorithm used by the linear CDC. Based on this we found that a float of 13.3 inches would theoretically be able to measure a .25cm height difference.
Conclusion
Based on our calculations, we found that an orifice of 8cm would give us an acceptable energy dissipation rate of .927 W/kg and would require a 13.3in float. This float would have a .25cm sensitivity over a 15.2cm height difference.
Wiki Markup |
---|
{latex} where D.actual is the difference between the given diameter of the dosing tube and the measured diameter of the dosing tube The size of the float can be determined using a moment balance around the pivot of the lever arm. This is to ensure that a change in head in the entrance tank will cause a similar change in the relative height of the float. The float was sized using the same float sizing algorithm used by the linear CDC. Based on this we found that a float of 13.3 inches would theoretically be able to measure a .25cm height difference. +(You made a jump here in logic that I don't see)+ h3. Conclusion Based on our calculations, we found that an orifice of 8cm would give us an acceptable energy dissipation rate of .927 W/kg and would require a 13.3in float. This float would have a .25cm sensitivity over a 20.3cm height difference. {float:left|border=2px solid black|width=300px} Non Linear Doser Diagram!head loss vs flow rate.jpg|width=300px, align=centrecenter! h5. Graph showing the non-linear relationship between the head loss vs. the flow rate through a 8cm diameter orifice {float} |
Additionally we found 2 solutions with multiple orifices. We did this because more orifices at a smaller diameter will keep energy dissepation constant while increasing overall headloss across the system. The first solution gave us 8 orifices with a 4.5cm diameter and a minimum energy dissipation rate of .831.
Wiki Markup |
---|
{float:left|border=2px solid black|width=300px}
!8 orifices.jpg|width=300px, align=center!
h5. Graph showing the non-linear relationship between the head loss vs. the flow rate through eight 4.5cm diameter orifices
{float} |
The second solution gave us 175 orifices with a 2 cm diameter and a minimum energy dissipation rate of .496.
Wiki Markup |
---|
{float:left|border=2px solid black|width=300px} !175 orifices.jpg|width=300px, align=center! h5. Graph showing the non-linear relationship between the head loss vs. the flow rate through 175 2cm diameter orifices {float} +(Include a section about how you can make these equations scalable for larger and smaller plant sizes.)+ |