Laminar Tube Flocculator
Overview: Objective and Motivations
Introduction
In the flocculation process, suspended particles collide with each other to coagulate and transform into larger flocs, with the help of a coagulant, that can be removed by sedimentation. To improve the performance of flocculators, we need to research how the design and operational parameters affect the aggregation and settling velocity of the flocs. These parameters include energy dissipation rate, hydraulic residence time, coagulant dose, influent turbidity, etc. One Water turbidity is caused by colloidal particles in suspension (and the presence of natural organic matter and other organic and inorganic contaminants). These colloidal particles are too small to settle, and due to their negatively charged surfaces, they electrostatically repel each other. Flocculation transforms these repelling colloidal particles to attract and form into flocs that are large enough to settle out in the sedimentation tank. The probability (collision potential) that particles collide in a flocculator depends on the energy dissipation rate and residence time in the flocculator. As flocs collide, they grow in size making it easier to remove them in subsequent processes. One of the goals for the AguaClara team is to develop a sedimentation tank that will form a fluidized floc blanket, which will help clean water as it flows into the sedimentation tank from the flocculator. To develop this floc blanket the flocculator must produce flocs that fall within a particular range of settling velocity. Therefore, it is important to research the parameters that affect flocculation and the resulting floc size distribution.velocities. Our apparatus (flocculation residual turbidity analyzer or FReTA) is capable of measuring both settling velocity and residual turbidity under different flocculator operating conditions. Complete description and sketches of current apparatus setup can be found here.
Excerpt |
---|
The goals of the Laminar Tube Floc Team are to determine the parameters that will affect influent turbidity removal and to develop flocculation models as a guideline for flocculation design. |
Conventional design guidelines for a hydraulic flocculator are incomplete, and the dynamics of how physical parameters affect flocculation are not well understood. The goal of the Tube Floc Team is to determine the parameters (such as optimal energy dissipation rate, hydraulic residence time, etc.) that will produce quickly settling flocs that can remove the greatest percentage of the turbidity for a variety of influent water qualities and provide better guidelines in designing a flocculation system.
Figure 1. Experimental apparatusIf you are new to the team or would like to know more about the upkeep of our experimental setup, check out the basics. An excellent resource for information on the FReTA setup tube flocculator is Ian Tse's M.S. thesis: Fluid shear influences on hydraulic flocculation systems characterized using a newly developed method for quantitative analysis of flocculation performance. This thesis contains detailed Detailed information on the Process Controller states, rules, and set points as ProCoDA Software as well as descriptions of the data analysis process can be found in the appendix of this M.S. thesis.
...
Ongoing Research
...
Past Research Teams
Summer 2010 Tube Floc Research
-During the summer, the team focused on completing the unfinished experiments left by the team of Spring 2010 which included the FReTA verification test and the study on the variation of alum dosage and flocculator length.
-The team updated Data Processor by simplifying the overall code and reorganizing its structure. A new smoothing method was added (weighted smoothing) and bimodal fitting functions were created.
Test Suspension for FReTA (Fall-Summer 2010)
-Series of verification experiments were run by the team to verify the accuracy of the data recorded by FReTA.
Influence of flocculator length and alum dosage on flocculation (Fall 2009-Summer 2010)
-A variation of alum dosage and flocculator length was tested to see their effects on flocculation. This study lasted from the academic years of 2009-2010.
Fluid shear influences on flocculation
-Past research (Spring 2008) and MEng report on FReTA submitted on Spring 2010.
Team Presentations
* Determine the optimal orifice size for floc break up systems with four, eight, and sixteen clamps by gradually decreasing the clamp size based on the relationships between energy dissipation rate, floc size, terminal velocity, and clamp size until the flocculator performance worsens.
- Determine optimal positioning for floc break up points by comparing the residual turbidity of an evenly distributed clamp system with clamp systems that gradually decrease the number of clamps toward one or both ends of the flocculator. As residual turbidity decreases the flocculator performance improves.
- Compare the performance of tapered tube flocculation with regular tube flocculation. Design a tapered system -- small tube at the beginning, medium tube in the middle, and large tube at the end (same length for each size of the tubing) using 10 mg/L PACl dose and 28 m tube flocculator length (N://files.Cornell.edu/EN/aguaclara/RESEARCH/Tube Floc/Spring 2013/Experiments/Single PACl 10 mgL.pcm/). As tube size (diameter) increases, energy dissipation rate decreases, allowing flocs to continue to grow. The larger that flocs can grow, the lower the residual turbidity will be.2. Determine optimal positioning for floc break up points by comparing the residual turbidity of an evenly distributed clamp system with clamp systems that gradually decrease the number of clamps toward one or both ends of the flocculator. As residual turbidity decreases the flocculator performance improves.
Current Research (Spring 2015)
* Design and implement a settled water turbidity (SWaT) measurement system that can more accurately measure low turbidities than the previous FReTA system. Using this new SWaT system, repeat experiments using only one clamp of variable size on the middle of the tubing arrangement. Compare the results of these experiments with the results of the same experiments run using the FReTA system from the Fall 2013 research.
* Depending on the results of the middle-clamp testing, either run more experiments with variable number of clamps to further test the effects of clamps, or design and implement a tapered flocculator system with energy dissipation rates starting from 1000 mW/kg.
Challenges for Future Semesters
- Special Skills Needed:
More Information
Troubleshooting of the apparatus, Process Controller and Data Processor.
Section | ||||||
---|---|---|---|---|---|---|
|
Column |
---|