Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Comment: Migration of unmigrated content due to installation of a new plugin

Include Page

...

2D Steady Convection - panel

...

2D Steady Convection - panel

...

Include Page

...

titleUnder Construction

...

This page is under construction. Please return later for updates

FLUENT Google Analytics
FLUENT Google Analytics

Mesh

Launch the Mesher

Now that we have completed creating the geometry of the domain, we are ready to mesh it. The meshing step chops up the domain into little chunks called cells or elements. The solver approximates the governing equations and/or boundary conditions on each of these chunks. The end result is a large system of simultaneous algebraic equations which we hand over to the computer to solve.

Return to the Project Schematic Window. In the Project Schematic this window, double click the Mesh box to launch the mesher.

Image Added

Twiddle your thumbs and try to avoid checking facebook while the meshing application launches. If a Meshing Options window shows up to the right, you can dismiss it.

Mapped Face Meshing

Note

For users of ANSYS version 16, mapped face meshing is now called Face Meshing.

 

First we will apply a "mapped face meshing. First, in " to get a regular mesh. In the Outline window, click Mesh to Image Added in the tree. This will show the Mesh menu meshing options in the main menu bar (look just above the tree outline). In the Meshing Menumeshing options, select Mesh Control > Mapped Face Meshing.

Image Added

In the Graphics window, click on the domain face rectangle to select it, then in the Details window, click Geometry > Apply.

Image Added

This will apply "Mapped Face Meshing" to the rectangle which will yield a regular mesh.

Edge Sizing

We will control the mesh size by specifying the size of the divisions to be used on the edges of the rectangle. To create the edge sizings, go to make sure Mesh is highlighted in the tree. Then select Mesh Control > Sizing.

Image Added

We'll be applying the sizing in meters. So check that the units are set to Metric (m, kg ...).

Image Added

Since we'll be applying the sizing to edges, . Next, we need to select the edge selection filter Image Removed. Click by clicking on it.

Image Added

Select Zoom to Fit as shown in the snapshot below to fit the entire geometry in the graphics window. Hold down the left mouse button and drag over the four horizontal edges (two top and two bottom). The surfaces will be highlighted in green when they've been selected.

Image Added

bottom, and top two surfaces (remember, the top surface has been split into two surfaces). In the details window, select Geometry > Apply. Now the mesher knows which edges to apply the sizing to. Ensure that Type is set to Element Size, then change the Size from Default to .1. 0.05 m as shown below. This will set each division size on the corresponding edges to 0.05 m. (If we want a finer mesh, we would input a smaller size.)

Image Added

Now, we will create an edge sizing for the vertical edges of the geometry. Create another edge sizing, and this time, choose the left and right vertical edges of the geometry by holding down the Ctrl key and selecting each of them, and go to Geometry > Apply. Change the Type to Number of Divisions. Next, specify Number of Divisions to 30. Note that one can specify the Element Size or Number of Divisions to 20.depending on which is more convenient.

Before generating the mesh, we will turn off the Advanced Sizing Function . Make sure that Mesh is highlighted in the tree and in the Details window, expand Sizing. Next to Use Advanced Size Function, change from On to Off

Generate the Mesh

In the Mesh context menu, Mesh > Generate Mesh.

Image Added

The generated mesh should now be seen. (If you don't see it at first, select Image Added in the tree outline to show the generated mesh). You can zoom in/out using the middle mouse wheel. We see that ANSYS decreases the mesh size near the entrance since it sees a corner. This is fine for our case since this will better resolve the rapidly developing boundary layer near the entrance. So we won't override this.

Named Selections

Next, we will have to specify names of different portions of the geometry to use in FLUENT to define boundary conditions. Make sure the Edge Selection Filter Image Added is selected before proceeding.

Inlet

Select the left, vertical edge of the geometry with a left mouse click - it should highlight green. Right click, and select Create Named Selection. Name the selection Inlet. Click OK once finished.

Centerline

Next, we will specify the axis/centerline of the pipe. Select the bottom surface of the pipe, and create a named selection. Name it Centerline.

Isothermal Wall

We will now specify the portion of the wall that is isothermal. Select the left portion of the upper surface of the pipe. Create a named selection and call it Isothermal Wall.

Heated Wall

We will now specify the portion of the wall that is heated. Select the right portion of the upper surface of the pipe. Create a named selection and call it Heated Wall.

Outlet

We will specify the outlet of the pipe. Select the right, vertical edge of the pipe. Create a named selection, and call it Outlet.

Flow Domain

Finally, we specify the flow domain of the pipe. With the face selection filter, select the face of the pipe. Right click and create a named selection and call it flow domain.


Image Added

newwindow
Click here to enlarge
Click here to enlarge
https://confluence.cornell.edu/download/attachments/146921317/named_selections_wflowdomain.png?version=1&modificationDate=1305338948000
 

Click Image Added to update all the changes made in the mesher.
now generate. We are done with the mesh creation, so we can now Image Removedsave the project, and close the mesher.

Go to Step 4: Physics Setup

Go to all FLUENT Learning Modules