Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Wiki Markup
{alias:curvedbeam}
{panel}
Author: Rajesh Bhaskaran, Cornell University

{color:#ff0000}{*}Problem Specification{*}{color}
[1. Start-up and preliminary set-up|ANSYS - 3D Curved Beam step 1]
[2. Specify element type and constants|ANSYS - 3D Curved Beam step 2]
[3. Specify material properties|ANSYS - 3D Curved Beam step 3]
[4. Specify geometry|ANSYS - 3D Curved Beam step 4]
[5. Mesh geometry|ANSYS - 3D Curved Beam step 5]
[6. Specify boundary conditions|ANSYS - 3D Curved Beam step 6]
[7. Solve\!|ANSYS - 3D Curved Beam step 7]
[8. Postprocess the results|ANSYS - 3D Curved Beam step 8]
[9. Validate the results|ANSYS - 3D Curved Beam step 9]
{panel}

h2. Problem Specification

The problem considered here is the curved beam of uniform trapezoidal         cross-section in example 6.15 of  [Cook et al.|ANSYS - Reference] 3D Curved Beam step 9 #ref]. The beam is bent in its own plane by moments M. The problem is          not axisymmetric because displacements have circumferential as well as          radial and axial components. So we use 3D solid elements rather than axisymmetric          elements. The geometry can nevertheless be described in cylindrical coordinates.

!beam2.jpg!

We would like to obtain the stresses for the trapezoidal cross-section          AA shown above. Stresses in the curved beam do not vary with θ, so          we can reduce the model and analyze only a typical slice between two closely          spaced radial planes as shown below. The angle between AB and CD is taken          to be 5 deg. as suggested by [Cook et al|ANSYS - 3D Curved Beam step 9 #ref].

!beam_nomesh.jpg!

The bending moment _M_ must be applied indirectly in the reduced          model since we don't know _a priori_ the circumferential stress distribution          it produces on the cross-section. Instead, we'll prescribe _displacements_ such that radial plane sections remain plane and a pure moment load acts          on the model i.e. no net force acts on it. The moment _M_ can be          computed from the stress distribution on the cross-section obtained from          FEA. Stresses scale linearly with the applied moment. So the stresses          associated with a prescribed moment _M{_}{_}{~}p{~}_ can be obtained          by multiplying the computed stresses by the ratio _M{_}{_}{~}p{~}{_}_/M_.

The z-constant plane containing A,B,C and D is a symmetry plane. So only          half the cross-section needs to be modeled.

h4. Boundary Conditions

The nodal d.o.f. in the radial (u), circumferential (v), and axial (w)          directions are constrained as follows:
| *Face                1* | *Face                2* |
| _u_=0 at node A | . |
| _v_=0 at all nodes | _v_=0.0001(r{~}c~\-r)at all nodes |
| _w_=0 along AB | _w_=0 along CD |
All remaining d.o.f. are unrestrained. Setting u=0 at A prevents rigid          body motion in the r-direction. Setting v=0 on face 1 nodes prevents circumferential          motion of face 1. Setting w=0 on ABCD imposes symmetry about the middle          r-θ plane. The above BC on face 2 nodes causes face 2 to remain plane          as it rotates about a z-parallel axis at r=r{~}c~. The factor 0.0001          is arbitrarily chosen. At the outset, the appropriate value of r{~}c~ is not known. The right value of r{~}c~ will give a pure bending          load so that the radial reaction R{~}A~ at node A is zero. Two          preliminary FE analysis with guess values of r{~}c~=60mm and r{~}c~=70mm          were done. The respective R{~}A~ values turn out to be 2001N and          357N. By linear extrapolation, R{~}A~=0 when r{~}c~=72.2mm.          So we'll use r{~}c~=72.2mm in our analysis. (Since this is a pedagogical          exercise, I've decided to be nice and give you the r{~}c~ value          to use. In the real world, you'd of course have to figure it out yourself).

Go to [Step 1: Start-up and preliminary set-up|ANSYS - 3D Curved Beam step 1]

[See and rate the complete Learning Module|ANSYS - 3D Curved Beam]

[Go to all ANSYS Learning Modules|ANSYS Learning Modules]